Skip to content
Thousand Rivers Partners
Language: EN
Contact us

How gold is recovered: gravity, leaching and the mercury ban

The main ways gold is recovered from ore, gravity, carbon-in-leach and heap leach, what decides which one a deposit needs, and why mercury is off the table.

7 min read

Gold in the ground is only worth the share of it a plant can recover. Two deposits with the same grade can be very different businesses if one gives up 90% of its gold to a simple process and the other gives up much less, or needs an expensive extra step first.

The processing route is set by the ore, not by preference. It drives the capital cost, the running cost, the permits and the waste a mine leaves behind. So it belongs near the top of any review, next to the resource estimate.

What the ore decides

Three questions shape the choice.

The first is how big the gold particles are. Coarse gold, visible grains and flakes, can be caught by gravity because it’s so much heavier than the rock around it. Fine gold, often far too small to see, has to be dissolved out chemically.

The second is what the gold sits in. Free-milling ore releases its gold once it’s ground fine, and that gold dissolves readily. Refractory ore locks the gold inside sulphide minerals such as pyrite or arsenopyrite, or holds carbon-rich material that grabs dissolved gold back out of solution (preg-robbing, in the industry’s term). Refractory ore needs a pre-treatment step before ordinary leaching works.

The third is whether the ore is oxidised. Near the surface, especially in a wet tropical climate like Kalimantan’s, weathering breaks down sulphides and leaves oxide ore that’s softer and easier to leach. Deeper down the same deposit often turns to fresh sulphide ore, harder and sometimes refractory. A mine plan built on oxide recoveries can face a sharp change when the pit reaches the sulphides.

Metallurgical testwork answers these questions. Samples from across the deposit, at different depths and from each ore type, go through grinding, gravity and leach tests in a laboratory. A project without that testwork is guessing at its recovery.

Gravity recovery

Gravity is the oldest method and the cheapest to run. Sluices, jigs, shaking tables and centrifugal concentrators separate heavy gold from lighter material using water and motion. No chemicals are needed to catch the gold.

For alluvial deposits, where the gold has already been freed by weathering and carried by rivers, gravity is usually the whole process. The article on alluvial gold covers that business. In hard-rock plants, a gravity circuit often sits inside the grinding circuit to catch coarse gold early, before the ore goes on to leaching.

Gravity’s limit is fine gold. Particles that are very small, flat or still attached to rock wash past the equipment. A gravity-only operation on ore with mostly fine gold loses much of it to the tailings.

Carbon-in-leach and carbon-in-pulp

Most hard-rock gold mines use cyanide leaching with activated carbon. Ore is crushed and ground to a fine powder, mixed with water into a slurry and run through a series of large tanks with a dilute cyanide solution. The cyanide dissolves the gold. Activated carbon in the tanks absorbs it.

In carbon-in-leach (CIL), leaching and absorption happen in the same tanks. In carbon-in-pulp (CIP), the slurry is leached first and then meets the carbon in later tanks. The loaded carbon is stripped of its gold, the gold is recovered from the solution by electrowinning and smelted into doré bars, a mix of gold and silver that goes on to a refinery. The article on selling gold picks up from there.

On free-milling ore, these plants can recover a high share of the gold, and that’s why they’re the standard choice. They cost a lot to build, though. Grinding is the most energy-hungry step in the plant, which matters at a remote Kalimantan site with no grid connection, where power often comes from diesel. The plant also needs a reliable water supply and a tailings storage facility.

Heap leaching

Heap leaching trades recovery for cost. Ore is crushed, or sometimes stacked as mined, onto large pads lined with plastic and clay. A dilute cyanide solution is sprinkled or dripped over the heap and trickles through it, dissolving gold on the way down. The solution is collected at the base and the gold is recovered from it, usually with carbon.

There’s no fine grinding and no tank farm, so the capital and running costs are lower, and ore of lower grade can be treated. Recovery is lower too and takes months rather than days. Heap leaching works best on oxide ore that lets solution flow through it. Clay-rich ore can clog a heap.

Rainfall is a real issue in Kalimantan. A heap leach is a water balance problem: every litre of rain that falls on the pads joins the process solution and has to be held, treated or used. Heavy tropical rain makes that harder and raises the risk of overflow, so a study for a Kalimantan heap leach needs its water design checked closely.

Refractory ore

When gold is locked in sulphides, the ore, or a concentrate made from it by flotation, is pre-treated to break the sulphides down before leaching. The main options are roasting, pressure oxidation in an autoclave and bacterial oxidation. All of them add a large capital cost and their own environmental questions, such as handling arsenic released from arsenopyrite.

A refractory deposit can still be a good mine, but it needs a higher grade or a larger scale to pay for the extra step. Some projects mine the oxide cap first with a simpler plant and leave the refractory ore for later, which only works if the later decision is funded and planned.

Cyanide, tailings and permits

Cyanide is toxic, and its transport, storage and use are tightly controlled. In Indonesia it counts as a hazardous and toxic material (bahan berbahaya dan beracun, B3), so its handling has to be covered by the mine’s environmental approval and the permits that come with it. Many mines and their lenders also follow the International Cyanide Management Code, a voluntary industry standard.

Tailings, the ground rock left after leaching, are stored behind a dam or in a dedicated facility. They have to be detoxified and kept stable for decades after the mine closes. That cost and responsibility carries into closure, as reclamation and closure explains.

The mercury ban

Mercury amalgamation is the shortcut small miners use. Mercury binds fine gold into an amalgam, which is heated to drive the mercury off into the air, leaving gold behind. It’s cheap and it works, and it poisons the workers, the river and everyone downstream.

Indonesia ratified the Minamata Convention on Mercury through Law 11 of 2017. Presidential Regulation 21 of 2019 set a national target to eliminate mercury from small-scale gold mining by 2025, a date that has now passed. Mercury has no place in a licensed operation, and a plan that relies on it shouldn’t be funded. Where earlier diggers used it, the contaminated tailings and sediment can become part of the clean-up for whoever takes over the area. Buyers and refineries also ask more questions about gold that might come from mercury-using sources.

What to ask for

Before you rely on a project’s recovery figure, ask for these:

  • The metallurgical testwork reports, with the laboratory, the number of samples and where in the deposit each sample came from.
  • Separate recoveries for oxide, transitional and fresh ore, and the tonnes of each in the mine plan.
  • Whether any of the ore is refractory or preg-robbing, and how the study deals with it.
  • The plant’s power and water sources, and the cost assumed for each.
  • The tailings design, the cyanide management plan and how both are covered in the environmental approval.
  • For any area with past small-scale mining, a survey of mercury contamination and an agreement on who carries the clean-up.

Then check that the recovery used in the economics matches the testwork for each ore type, year by year. The article on gold project economics shows where it feeds in.

General information, not legal, tax or investment advice. Rules change, so confirm the current regulation with a notary or lawyer before you act.