Biogas from palm oil mill effluent
How palm oil mills capture methane from their effluent (POME), what the gas can power, what the projects cost to run and where emission credits fit in.
5 min read
Every palm oil mill produces large volumes of warm, oily wastewater. It’s called palm oil mill effluent (POME, in Indonesian limbah cair pabrik kelapa sawit). Most mills in Kalimantan still treat it in a row of open ponds, where bacteria break it down and release methane into the air.
Methane is a strong greenhouse gas, and it’s also a fuel. Covering the ponds or building tanks to capture it turns a pollution problem into a source of energy. It’s one of the more established clean energy projects in the palm industry, and one of the few that a single mill can do on its own site.
Where the effluent comes from
POME is mostly water from sterilising the fruit, from the clarification of the oil and from washing equipment. It’s hot, acidic and full of organic matter. Untreated, it would kill a river.
Engineers often work with figures of about 0.6 to 0.7 cubic metres of effluent per tonne of fruit processed, though the real number depends on the mill’s equipment and how carefully it uses water. A mill processing several hundred thousand tonnes of fruit a year produces a lot of it. Measure the actual flow at the mill before relying on any rule of thumb.
Indonesia sets limits on what may be released, in its wastewater quality standards for the palm oil industry. Many mills don’t discharge to rivers at all. Instead they use the treated effluent on their estates as fertiliser (land application), which needs its own permit and monitoring. Ask to see both the standard the mill reports against and its permit.
How methane is captured
There are two common designs.
A covered lagoon puts an airtight membrane, usually a thick plastic sheet, over one of the existing anaerobic ponds. Gas collects under the cover and is piped away. It’s the cheaper option and uses land the mill already has, but the ponds fill with sludge over time and the gas output can vary.
A tank digester, often a continuously stirred tank reactor, treats the effluent in closed steel or concrete tanks. It costs more to build, but it gives more control over temperature and mixing, takes less land and usually produces steadier gas.
Both designs need pre-treatment to cool the effluent and remove oil and solids, a gas cleaning step to strip out hydrogen sulphide, which corrodes engines, and a flare to burn off gas the mill can’t use. The flare matters, because a project that captures gas but vents it during outages loses most of its climate benefit.
What the gas can power
Biogas from POME is roughly 50 to 70% methane, and the rest is mostly carbon dioxide. Mills use it in a few ways:
- Electricity from gas engines, for the mill itself, its housing or the grid. Selling surplus power to the state utility is covered in selling mill power to PLN.
- Fuel for the mill’s boilers, in place of fibre and shells, which frees those for sale.
- Heat or power for a nearby plant, such as a kernel crushing plant or a refinery.
- Bio-compressed natural gas, cleaned and compressed for trucks or industry, covered in bio-CNG and mill energy projects.
The best use depends on where the mill is. A mill far from the grid that runs diesel generators for its housing and workshops gets clear savings from biogas power. A mill already burning its own fibre for all its steam and power needs a buyer for the extra energy, or the project has little to replace.
The economics
The capital cost depends on the design, the size of the mill and how far the gas or power has to travel. Covered lagoons sit at the low end. Tank digesters with gas engines and grid connections sit well above. Get quotes from at least two engineering firms that have built POME plants in Indonesia, and ask to visit one of their projects.
Running costs come from maintenance of engines and covers, sludge removal, the gas cleaning system and skilled staff. Engines in particular need regular overhaul, and spare parts may have to come from Java or abroad.
The value side has three parts: the fuel or power the gas replaces, any income from selling power or gas, and any income from emission credits. The first is the most reliable. The others depend on contracts and markets that can change.
A project that only works if the credit price is high is fragile. Build the case on energy savings first and treat credits as a bonus.
Emission credits and certification
Methane capture was one of the most common project types under the Clean Development Mechanism, the Kyoto Protocol’s credit scheme, and many Indonesian mills registered projects there. Those credits are mostly history now.
Today, credits can come from voluntary standards or from Indonesia’s own carbon market, under the economic value of carbon (nilai ekonomi karbon, NEK) rules. Any project in Indonesia has to be recorded in the national registry (Sistem Registri Nasional Pengendalian Perubahan Iklim, SRN-PPI) before credits can be traded. The article on the carbon market in Indonesia explains how that works, and the rules were still changing in 2026, so confirm the current process with the environment ministry or an adviser.
Methane capture also counts in other ways. Buyers of palm oil and of biofuel feedstock look at the emissions of the oil they buy, and a mill with methane capture can show lower figures. That can help with sustainability certificates such as the Roundtable on Sustainable Palm Oil (RSPO) and with bioenergy certificates (see bioenergy certification), even where it brings no direct payment.
What to check first
If a mill you’re looking at has a biogas plant, or a seller pitches one:
- Is the plant running now? Ask for gas flow, engine hours and flare records for the last two years.
- What does the gas replace, and what’s that worth at current fuel and power prices?
- Who built it, who maintains it and where do spare parts come from?
- Are there contracts for power, gas or credits, and how long do they run?
- Is the project in the national registry, and are any credits already sold or promised to someone else?
- What’s the state of the effluent permits, and has the mill had any complaints or violations?
A biogas plant that sits idle is common. Many were built for credits that later lost their value, so check that it runs before paying for it.
General information, not legal, tax or investment advice. Rules change, so confirm the current regulation with a notary or lawyer before you act.